Flydumps-2016 Hottest Cisco 350-040 Questions And Answer Study Guide Ensure You 100% Pass

Posted on By testsectd

Exam A
QUESTION 1
On a standalone switch, all ports in VSAN 9 are administratively shut down. What is the operational state of VSAN 9?
A. Up
B. Initializing
C. Active
D. Suspended
E. Down
Correct Answer: E
QUESTION 2
There are three different roles on the MDS:

Role1 allows show commands only.
Role2 allows debug and configure commands, and denies show command.
Role3 permits VSAN 10-30 only.

User1 belongs to Role1, Role2 and Role3. What can User1 do?

A. Show,debug, and configure on VSAN 10-30
B. Debug and configuration commands on VSAN 10-30
C. Show, debug, configure on all VSAN
D. Debug and configure commands only on all VSAN
E. Show,debug, configure and save configuration on VSAN 10-30
Correct Answer: C
QUESTION 3
What statement is true?
A. Class of Service 1 frames are acknowledged only when requested by the sender.
B. R_RDY is the correct way to acknowledge a Class of Service 1 frame.
C. Class of Service 1 and 2 reserve 100% of the available bandwidth.
D. Class of Service 3 framesrequire an ACK1 response.
E. Class of Service 2 frames are acknowledged by an ACK response.
Correct Answer: E

QUESTION 4
What is the purpose of the Open Fibre Control system?
A. It defines a safety mechanism for SW laser data links.
B. It specifies the maximum bit error rate for Fibre channel links.
C. It defines the distance limitation for different types of lasers.
D. It defines the mechanism in which Fibre Channel switches communicate with Gbics.
E. It defines the flow control mechanism for Fibre Channel.
Correct Answer: A

QUESTION 5
What SW_ILS frame is used to perform Principal Switch Selection?
A. ELP
B. RDI
C. DIA
D. ESC
E. EFP
Correct Answer: E
QUESTION 6
Which is the objective of the SW_ILS ELP frame?
A. Notify other switches they can now request domain IDs
B. Notify other switches that a principal switch has been elected
C. Exchange FSPF routing information
D. None of the above
Correct Answer: D
QUESTION 7
Select the true statements concerning the IP address subnetting requirements of gigabit Ethernet interfaces on the IPS-8 module:
A. Interfaces gigabitethernet1/1.10 and gigabigethernet2/1.10 must be configured with IP addresses in the same subnet
B. Interfaces gigabitethernet1/1 and gigabigethernet2/1 can be configured with IP addresses in the same subnet
C. Interfaces gigabitethernet1/1 and gigabigethernet1/2 can not be configured with IP addresses in the same subnet
D. Interfaces gigabitethernet1/1 and mgmt0 can not be configured with IP addresses in the same subnet
E. Interfaces gigabitethernet1/1.10 and gigabigethernet2/1.12 can be configured with IP addresses in the same subnet
Correct Answer: BD
QUESTION 8
Node is logged into port fc1/1 in VSAN 4000. If VSAN 4000 is deleted then what will happen?
A. Invalid – VSAN 4000 is not available.
B. Node will move to VSAN 1.
C. Node will move to VSAN 4095.
D. Node will move to VSAN 4094.
E. Invalid – VSAN can not be deleted until all members are removed.
Correct Answer: D
QUESTION 9
On a standalone switch, VSAN 10 has 10 active ports. When a “no vsan 10” command is issued on the switch what is true?
A. VSAN 10 will not be deleted as it has active ports.
B. VSAN 10 will be deleted and the ports moved to VSAN 4094.
C. VSAN 10 will not be deleted and the ports moved to VSAN 4094
D. Vsan 10 is deleted and the ports moved to VSAN 4093
E. VSAN 10 will be deleted and the ports moved into VSAN 1
Correct Answer: B
QUESTION 10
FC1/1 is a member of VSAN 1. After the command “no VSAN 1” is entered, FC1/1 will be a member of what VSAN?
A. VSAN 4094
B. VSAN 1
C. VSAN 4093
D. VSAN 0
E. VSAN 4095
Correct Answer: B